Features

Design benefits

compatibility

This motor is compatible with the FLTB-5 V2 (models from 2023) and FLTB-9.

easy assembly / dismantling

Slide it into the base under the float tube then install the safety pin.

ease of use

The variator is used to precisely adjust the forward and reverse speed.

noise level

A quiet motor for discreet movements when fishing.

Design details

SAFETY

Always use your boat and this motor in accordance with the local safety regulations. When onboard your boat, you must always have a life jacket, in accordance with the local regulations, and a paddle or fins for use in the event of a breakdown. Only for use by adults. Do not start the motor out of the water. Take care when close to the propeller to avoid injury.

INSTALLING THE MOTOR AND THE CONTROL UNIT

This motor is compatible with float tubes and kayaks equipped with the Decathlon fin base. (Reference: 8603033) Always disconnect the circuit breaker of the control unit before taking any other action. Insert the motor into the base under the boat, then install the safety pin. Connect the signal wire between the motor and the control unit. Check that the wire is properly assembled and watertight.

BATTERY CONNECTOR (not included)

The motor is designed for use with a 12 V battery. Depending on the battery used, the casting weight will be between 24 and 32 lbs. We recommend sealed lithium technology batteries, which are lighter and more compact. You'll need to adjust the connector based on the type of battery that you're using. 2 clamp connectors provided. The red wire must be connected to the positive terminal and the black wire to the negative terminal.

CONSUMPTION

Full power forward: 25 Amps, accurate to 23.63A (320w) Full reverse: 21.2 Amps max (263w) Average continuous current at half throttle = 5 Amps Using the motor at half throttle means very high savings on long journeys. A 12Volt 50Ah battery is therefore an ideal choice for a day's fishing.

GETTING STARTED

1. Put the magnetic circuit breaker on the control unit. The other end must be attached to the user. Set to 0. The LED must be green. 2. Forward/reverse operation of the motor is controlled using the rotary switch on the control unit. 3. You can use the variator on the control unit to drive the boat forwards or backwards and to adjust the speed. 4. Use fins or paddles to steer your boat.

CHARACTERISTICS, DIMENSIONS AND WEIGHT

MOTOR: Power in WATTS : 240W Casting weight in lbs: Between 24 and 32 lbs depending on the battery used Nominal voltage: 12 Volts Input voltage range: 9–17 Volts Operating current: 18 Amperes Watertightness standard: IPX8 Total dimensions: 25 x 18 x 19.5 cm (length x width x height) PROPELLER: 15 cm (diameter) CONTROL UNIT: 9 x 5.7 x 4.5 cm (length x width x height) 2.8 cm (diameter of the switch) Total weight: 3 kg

SPARE PARTS

The following parts are available on this web site or in our stores (to order): 8807567 FLTB MTR CONTROL UNIT 8807590 FLTB MTR CIRCUIT BREAKER 8807595 FLTB MTR PROPELLER 8807597 FLTB MTR PROPELLER SHIELD 8601075 PINS FOR CENTREBOARD (system that locks the motor into the base)

level of practice	all levels
place of practice	salt water, fresh water
motor position	middle position
motor power (in cv)	< 1.5cv
built-in battery	without built-in battery
motor power (in lbs)	32 Lbs
condition	new
power (in Watts)	250 W
motor control	throttle
engine type	in-boards

Raw material	96.14%
Manufacturing	0%
Packaging	0.726%
Distribution	2.206%
Use	0%
End of life	0.928%

FISHING FLOAT TUBE MOTOR FLTB MTR

Features

Design benefits

Design details

Specifications

Details

Composition

Usage & care

Care instructions

Usage precautions

Storage

Cleaning

Environmental impact

Carbon footprint