Features

Design benefits

waterproof

Validated in a simulator reproducing STORM conditions

breathability

Unlined three-layer breathable fabric (RET <20).

pockets

2 connecting fleece pockets. 1 compartmented front pocket.

resistance to salt water

Injected plastic zip.

Design details

WATERPROOF

- Membraned 3-layer fabric - A strong rain corresponds to a flow of 450L/m2/h - (= rainfall of 450 mm/h) - The rainfall simulator reproduces these conditions for 3*8 hours. - Component resistant to water pressure of 10,000 mm after ageing, = 10,000 Schmerber - average pressure of water during a storm - Water repellent components (water runs off the fabric). - 100% taped seams. - Central opening features a flap with a drainage channel for optimal waterproofing

EASY TO ADJUST

Two-way adjustable hood with semi-rigid visor and drainage channel. Synthetic rubber sleeve cuffs adjustable by rip-tab strips. Adjustable synthetic rubber neck. Adjustable neoprene waistband for a perfect fit with the overalls

BREATHABILITY

RET <20: breathable. To find out whether a fabric is breathable, we measure its evaporative resistance, or RET, (test based on the ISO 11092 standard). It is its ability to allow the water vapour produced by the body during exercise to escape.

Comfort

21 cm fleece collar (back) Weight: 1110 g in size L Fleece hand pockets Compartmented front pocket for a knife or VHF

REFLECTIVE

2 shoulder patches 2 hood patches intensifying sources of low light

RESISTANCE TO WEAR

Injected plastic central zip resistant to salt oxidation.Coating to prevent oxidation, which impairs membranes

HOW TO REACTIVATE THE ANORAK'S WATER REPELLENCY step 1: before washing

Close all zips and flaps and remove any parts of the garment that cannot be washed. Also remember to loosen the straps and elastic parts and empty the pockets. Then turn the garment inside out to wash it.

HOW TO REACTIVATE THE ANORAK'S WATER REPELLENCY step 2: washing

You can wash your jacket on a synthetic cycle at 30° or 40°C with your usual detergent. Do not use fabric conditi1r, which could damage the existing performance of the garment, or bleach. Also take care not to bend your jacket too much when you place it in the washing machine and do not overload your machine. Very important: select a thorough rinse or double rinse to completely remove all detergent residue.

HOW TO REACTIVATE THE ANORAK'S WATER REPELLENCY step 3: drying

Drying is a crucial phase in reactivating the water repellent treatment. We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator.Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

HOW TO REACTIVATE THE ANORAK'S WATER REPELLENCY

If, despite this procedure of washing and thorough rinsing followed by gentle drying in a tumble dryer, the drops of water no longer run off the surface of your jacket, we recommend that you "re-waterproof" it using a spray sold in our stores.

frequency	intensive
fit	loose
neck type	zip neck
number of pockets	3 pockets
zip type	full zip
waterproof	waterproof
hood	with hood
rain	heavy rainstorm
breathability	breathable
mm H2O (Schmerbers)	10,000 mm
windproof	windproof

Raw material	91.584%
Manufacturing	1.308%
Packaging	0.403%
Distribution	2.716%
Use	3.224%
End of life	0.764%

Offshore Race men's sailing boat jacket yellow

Features

Design benefits

Design details

Specifications

Details

Composition

Usage & care

Care instructions

Storage

Cleaning

Environmental impact

Carbon footprint