Features

Design benefits

thermal insulation

3mm full-body diving suit. Seams taped with GBS glued & blind-stitched assembly.

easy dressing

One-piece diving suit with back zip.

freedom of movement

Anatomic cut frees up arm movement. No seams under the armpits.

robustness

Reinforcements to reduce wear on the knees.

Design details

Details of thermal insulation and reinforcement

3 mm full-body one-piece wet type with back zip. Seams taped using a GBS (glued and blind stitched) assembly. Once a thin layer of water (that enters through the zip) gets trapped between your body and the diving suit, the water stays warm as it is not replaced. This thin layer of water keeps you warm. The diving suit has printed reinforcements on the knees to reduce wear.

GBS (glued and blind stitched) assembly

The diving suit's GBS assembly (Glued and Blind-Stitched) means that the seams are waterproof: the neoprene is glued first of all, then sewn for maximum strength (the sewing needle does not go completely through the neoprene in order to prevent water infiltration).

Why use a 3 mm diving suit?

Even in warm waters, the body ends up cooling down (25 times faster than in the air). Use a thin 3 mm diving suit that will allow you to delay this drop in temperature so that you can enjoy your activity for longer. In addition, use a full-body diving suit to fully protect you from UV rays and the underwater (coral, etc.).

Thermal performance class

This scuba diving suit provides thermal protection that has been tested by the independent INPP institute (Marseille, France) in order to validate its compliance with the current standard (EN 14225-1:2017). This diving suit is certified for use in waters warmer than 25°C.

What is a diving wetsuit?

This is the most common type of diving suit on the market. It is not designed to keep the water out, but to trap it, so that your body then warms it up, creating a thermal buffer between you and the outside. Made of neoprene - a rubber polymer filled with air bubbles - these diving suits are available in thicknesses of 0.5 mm to 7 mm. Thanks to their suppleness and modularity, they constitute excellent diving suits.

Tips on how to get into a diving suit

Put your foot in a plastic bag. Then put your leg into your diving suit. Your foot comes out completely and smoothly! To adjust, ask someone to blow into your sleeve from the wrist. The incoming air inflates the interior of the neoprene diving suit, immediately separating it from your skin. You can then easily proceed with the final adjustments.

Tips on how to take care of your diving suit

1) Soak the inside and the outside of the diving suit in clean water after each session, 2)Disinfect it with an antibacterial solution, 3)Rinse well with clean water, 4) Dry on a wide hanger in a dark and well-ventilated place. Caution: the sun will cause the colours of the textile parts of the diving suit to fade and speeds up the ageing process of the neoprene. Zips can be cleaned with a toothbrush and lubricated with silicone grease.

level of practice	beginner, all levels
water temperature	water > 25°C, warm water
type of opening/closing	zip
zip type	back zip
neoprene thickness	3 mm
age	over 14 years and adults
main material	neoprene
pocket	without pocket
number of pockets	pocket less
airtight/waterproof	not waterproof
type of length	long
condition	new
neck type	high neck
reinforced area	reinforced knees area
sleeves length	long sleeves
anti-uv	non anti-uv
sleeve finishing	without finishing
stitching type	glued and blind stitched
style	two-tone
balaclava	without balaclava
suit	integral

Raw material	92.478%
Manufacturing	0.264%
Packaging	0.003%
Distribution	1.598%
Use	4.548%
End of life	1.108%

Men's diving wetsuit 3 mm neoprene SCD 500 turquin blue

Features

Design benefits

Design details

Specifications

Details

Composition

Usage & care

Care instructions

Usage precautions

Storage

Cleaning

Environmental impact

Carbon footprint

Ecodesign approach