Features

Design benefits

waterproof

Tested in moderate rain for 2 h 5,000 mm Schmerber (JIS) Pockets not waterproof

breathability

Very breathable coated fabric (RET < 12): reduces condensation

pockets

2 secure pockets

windproof

Fabric especially coated to reduce the cooling effect of the wind

Design details

Waterproofing 1/2

We measure the fabric resistance to water pressure in mm of water column (based on the JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is. Here are the waterproofing ratings: Component resistant to water pressure of 5,000 mm before and after ageing (5 washes). This equates to 5,000 Schmerber - average pressure exerted by the water during rain. The jacket's waterproofing has been tested in a rain shower with 60 litres of water/m²/hour for hours

Waterproofing 2/2

- High collar - Injection-moulded plastic to avoid salt oxidation - Water-repellent components (water runs off the fabric) - 100% taped seams - Central opening features a flap with a drainage channel for optimal waterproofing

Hood

The hood does not pack down into the collar, it is attached. Hood is fully depth-adjustable but not in length. Due to regulations we cannot put an adjustment cord near the neck. Visor with a headband to provide a good level of protection and a better hold. The high neck effectively protects the neck.

pockets

2 zip pockets on the front of the jacket for your hands or a few items NOTE: the pockets are NOT WATERPROOF

Front zip closure

A zip on the entire jacket length with an interior flap protects against the wind and water. Soft fabric flap on the top of the collar to protect the chin.

Fabric breathability

To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability. We consider that if: RET < 9 = very breathable fabric 9 < RET < 12 = breathable fabric. The values for the Trek 500 jacket’s breathability are as follows: > More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard) > Lightest fabric: RET < 8 (or 2972 g/m² /2

Water-repellent properties information

A fabric is water-repellent when water slides off the surface of the fabric, without seeping in. Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered. The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.

How to wash your jacket?

To maintain the water repellent properties, infrequent washing is recommended. Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full rinse cycle or extra rinse.

How to reactivate the jacket's water repellency

Drying is a crucial phase in reactivating the water repellent treatment. We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator. Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

level of practice	beginner
frequency	occasional
rain	moderate rain
neck type	zip neck
type of opening/closing	zip
number of pockets	2 pockets
reversible	not reversible
silent	not silent
zip type	full zip
type of lining	light
snow skirt	without snow skirt
waterproof	waterproof, water repellent
age	5 years, 6 years, 10 years, 12 years, 8 years, 14 years
hood	with hood
pocket	inside pocket, zip closed pocket, with pocket, closed pocket
main material	polyester
breathability	breathable
fit	standard
style	two-tone, plain
membrane construction	2 layers
ventilation system	without ventilation
mm H2O (Schmerbers)	5,000 mm
condition	new
water-repellent	water repellent
windproof	windproof
lining material	synthetic
type of length	mid-long
reinforced area	without reinforced area
sleeves length	long sleeves
modular	not modular
stitching type	with seam
reflective	without reflective zones
type of waterproofing	coating
sleeve finishing	without finishing
breathability (in RET)	RET 6 < RET < 12 : moderately breathable
top length	standard
type of hood	hood with visor
storage	without storage

Kid's waterproof sailing jacket - wet-weather jacket SAILING 100 lavender pink

Features

Design benefits

Design details

Specifications

Details

Composition

Usage & care

Care instructions

Cleaning