Inflatable canoe kayak 2/3 person - Tribord 100+ Blue
This solid inflatable kayak with high-pressure Dropstitch bottom offers 3 raised seats for optimum comfort, combining stability and performance in complete safety.
ID 8940857
- 365 days to return for members
capacityFor 2 to 3 people, up to a maximum of 245 kg (540 lbs).
stabilityRaised seats & high sides for a relaxing paddle.
easy assembly / dismantlingInflates in 10 minutes with a dual action hand pump.
quick dryingIts tarpaulin construction allows faster drying.- Technical dimensions and weightsINFLATED SIZE: Length: 410 cm Width: 102 cm FOLDED & BAGGED SIZE: Height: 72 cm Width: 45 cm Thickness: 37 cm Weight: 18 kg Maximum floor pressure: 0.34 bar (5 psi) Side tube and seat pressure: 0.2 bar (3 psi) Number of seats: 2 or 3 seats Contents: kayak, bag, repair kit, 3 fins, user guide, inflation connector, strap. PUMP NOT INCLUDED Compatible with the TRIBORD multi-nozzle double-action hand pump
- Inflation tips and floor positioningConnect the pump (sold separately) using the 1⁄4 turn pump nozzle and inflate the bottom to 5 PSI. Finish by screwing the cap back on. Put the floor inside the kayak and strap it at the ends. The floor valve must be aligned with the side tube valves located at the back of the kayak. The floor's position must allow free access to the drain plugs located in the middle of the kayak.
- Side tube and seat inflation tipsConnect the pump (sold separately) using the 1⁄4-turn pump nozzle and inflate the tubes to 3 PSI. Finish by screwing the cap back on. Each side tube has a pressure relief valve. Its purpose is to evacuate excess air resulting from overinflation. When this happens, you may notice a hissing sound. This hissing sound is normal, it can also occur during prolonged exposure to the sun. It will stop once the kayak reaches the correct internal pressure.
- Seat comfort and positioning.The seats are high, providing increased comfort for adults in the paddling position. Position the seats on the floor using the rip-tab areas located under the seat and on the floor. Stow any bags or equipment into the kayak's rear hatch or attach to the rear deck. The boat is ready to be launched.
- Glide performanceThe deck of the kayak 100+ uses the same ’drop stitch’ construction as the inflatable stand up paddle boards. Dropstitch is a weave of polyester fibres sandwiched between 2 layers of PVC. When the deck is inflated to high pressure, the threads are stretched and the construction becomes very strong, thus avoiding any deformation.
- Care instructionsRemove the seats and slightly deflate the floor to make it easier to rinse out. Rinse the kayak, floor and seats with clean water after each use to avoid damage from sand, salt water and sun. Open the drain plugs located in the middle of the kayak and at the rear. Tip the kayak to empty out the water.
- Disassembly & foldingMake sure that the surface on which you intend to fold is clean . Remove the fins. Deflate the side bladders. The valves are located at the back of the kayak. PLEASE NOTE: Do not unscrew the pressure relief valves at the front. Fold the floor. Fold the rest of the kayak in half lengthwise. Flatten the front fin base. Lay the rolled floor on the front end. Roll the kayak to the rear end. Strap the kayak.
- StorageOnce dry and clean, the kayak should be stored in a dry and shady place, protected from significant temperature changes.The kayak can be stored folded but if you have enough space, storing it flat and slightly inflated will extend its life.
- After-sales serviceSpare parts are available for 100+ kayaks from after-sales service. Visit the workshop at your nearest Decathlon store to collect or order some. Drop Stitch floor: 8561072 Pressure relief valve: 8561069 Carry bag: 8605095 Paddle rip-tab: 8561070
- Directions for use.We recommend that you use the product with a buoyancy vest.
- regulations for canoes-kayaks measuring less than 3.50 metresIs your canoe-kayak inflatable or rigid and is less than 3.50 metres? You have what is called a beach craft. You must always stay within 300 metres of a shelter (any place on the coast where any craft or vessel and its crew can get to safety by anchoring or berthing, and set off again without assistance). Buoyancy life vests are not mandatory but strongly recommended to make it easier to get back in the boat if you fall out.
- regulations for canoes-kayaks measuring more than 3.50 metresYour canoe/kayak is rigid or inflatable with at least 2 separate air chambers. It measures more than 3.50 metres. It is approved for sea use by the manufacturer. You can paddle up to 2 nautical miles (approx. 3 km) from shore. You must carry a number of items of safety equipment. You can find a list of these items via this link: https://www.itiwit.fr/reglementation-pour-faire-du-canoe-kayak
Features
Design benefits
Design details
Specifications
Details
| level of practice | beginner, all levels |
| number of persons | 2 to 3 persons, 3 persons |
| maximum load | 240 kg |
| main material | polyvinyl chloride, polyamide |
| type of dinghy | inflatable |
| condition | new |
| weight (in kg) | 18 kg |
| width (in cm) | 102 cm |
| length (in cm) | 410 cm |
Composition
Main fabric: 60.0% Polyvinyl Chloride, 40.0% Polyester |
Usage & care
Environmental impact
Ecodesign approach
Analysing the product's environmental footprint enabled us to identify the most impactful stages of its life cycle. Thanks to this approach, our design teams were able to develop this product while significantly reducing its environmental impact.More about our approach
Repairability
Product designed to be repairable on more than 80% of breakages and failures.Repairability is the ability to offer a solution in the event of product breakage or failure. The repairability of a product is defined according to 4 criteria: - The availability of instructions on how to repair the product for customers - The possibility of disassembling the product - The availability of spare parts - The price of the repair is lower than purchasing a new product Our goal is to cover any possible known break or repair a product might have. We think about the life span of a product from the design stage, to ensure that it lasts as long as possible.